Tweco C-20C CutSkill Manuel d'utilisateur

PLASMACUTSKILL®Operation ManualPLASMA CUTTINGSYSTEMC-20C Rev. AA.01 Issue Date: March 26, 2007 Manual 0-4687 Operating Feature

GENERAL INFORMATION 1-4 Manual 0-46871.04 Statement of WarrantyLIMITED WARRANTY: Subject to the terms and conditions established below, Thermadyne®

Introduction 2-1 Manual 0-46872.0 INTRODUCTION2.01 INTRODUCTIONPlasma is a gas which has been heated to an extremelyhigh temperature and ionized so th

Introduction 2-2 Manual 0-46872.04 Torch SpecificationsArt # A-0465310.5 in (266.7 mm)3 in(76.2 mm)Torch ConfigurationTorch Head at 70° to Torch Hand

Installation 3-1 Manual 0-46873.0 Installation3.01 Site Selection• Place in a clean and dry area.• Provide adequate ventilation and fresh air sup-ply.

Installation 3-2 Manual 0-4687This Page Left Blank

Operation 4-1 Manual 0-46874.0 OPERATION4.01 Front Control Panel Overheating IndicatorAC Power IndicatorAir Error IndicatorTorch Switch Latch

Operation 4-2 Manual 0-46874.02 Preparations For OperatingAt the start of each operating session: WARNINGDisconnect primary power at the source befor

Operation 4-3 Manual 0-4687E. Typical Cutting SpeedsCutting speeds vary according to torch output, the type of material being cut, and operator skill.

Operation 4-4 Manual 0-4687This Page Left Blank

Manual 0-4687 5-1 SERVICESECTION 5:SERVICE5.01 Basic Troubleshooting GuideWARNINGThere are extremely dangerous voltage and powerlevels present inside

SERVICE 5-2 Manual 0-46872. Poor Work Lead connection.a. Check the connection of the Work Lead to thework piece.Make a clean work cableconnection to

Manual 0-4687 A-1 APPENDIXAppendix 1: Operating Sequence, Block DiagramPrimary Input Power "On" or Plugged inGreen Power Indicator "O

APPENDIX A-2 Manual 0-4687Appendix 2: Torch ConnectionDisconnect power and air. Lay unit on its side. Remove two screws and access plate. Pilot Powe

Manual 0-4687 A-3 APPENDIXAppendix 3: System SchematicInput AC115/230V1PHFilter & InputSelectorDiodeFanCompressor InputSelectorCompressorPressur

APPENDIX A-4 Manual 0-4687This Page Left Blank

Thermadyne USA2800 Airport RoadDenton, Tx 76207 USATelephone: (940) 566-2000800-426-1888Fax: 800-535-0557Email: [email protected] Canada

Corporate Headquarters16052 Swingley Ridge RoadSuite 300St. Louis, MO 63017Telephone: 636-728-3000Email: [email protected]

WARNINGSRead and understand this entire Manual and your employer’s safety practices before installing,operating, or servicing the equipment.While the

TABLE OF CONTENTSSECTION 1:GENERAL INFORMATION ... 1-11.0

Manual 0-4687 1-1 GENERAL INFORMATIONSECTION 1:GENERAL INFORMATION1.01 Notes, Cautions and WarningsThroughout this manual, notes, cautions, and warnin

GENERAL INFORMATION 1-2 Manual 0-4687• Wear dry gloves and clothing. Insulate yourselffrom the work piece or other parts of the weldingcircuit.• Repa

Manual 0-4687 1-3 GENERAL INFORMATION6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USEOF CUTTING AND WELDING PROCESSES, obtain-able from American Nat