Tweco Torch Data for Auto-Cut O2 V.1 Manuel d'utilisateur télécharger pdf (Page 35)

Manual 0-4831 Rev. AH 8-41 TORCH DATA for AutoCut O

(ga) (in) inch psi Ball psi Ball psi Volts

(in)

±0.005

(ipm) (in) (sec) (in)

1/2 0.500 20 120 100 8 55 160 0.200 120 0.300 0.3 0.161

5/8 0.625 20 120 100 8 55 164 0.200 100 0.300 0.4 0.165

3/4 0.750 20 120 100 8 55 170 0.250 80 0.500 0.5 0.174

7/8 0.875 20 120 100 8 55 173 0.250 70 0.500 0.6 0.175

1 1.000 20 120 100 8 55 175 0.250 60 0.500 0.7 0.190

1 1/4 1.250 20 120 100 8 55 180 0.250 40 0.500 1.2 0.185

1 1/2 1.500 20 120 100 8 55 184 0.300 25 0.190

1 3/4 1.750 20 120 100

55 196 0.300 15 0.213

2 2.000 20 120 100

55 200 0.300 10 0.205

bar Ball bar Ball bar Volts

(mm)

±0.1

(mm/min)

(mm) (sec) (mm)

1.4 120 6.9 8 3.8 163 5.1 2680 7.6 0.4 4.2

1.4 120 6.9 8 3.8 171 6.4 1960 12.7 0.5 4.4

1.4 120 6.9 8 3.8 175 6.4 1560 12.2 0.7 4.8

1.4 120 6.9 8 3.8 180 6.4 1000 0.2 1.2 4.7

1.4 120 6.9 8 3.8 184 7.6 640 4.8

1.4 120 6.9 8 3.8 195 7.6 400 5.4

1.4 120 6.9

3.8 199 7.6 270 5.2

* Pressure of the water supply line should be regulated by customer pressure regulator.

Note1:

Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the

ohmic sensing circuit.

Note2:

Water source used for shield must be demineralized.

BOLD TYPE

indicates maximum piercing parameters.

BOLD ITALIC

indicates edge starts only.

Requires CCM version 3.4 or later. Requires GCM version 3.2 or later

Edge Start

Shield

Retainer

Shield Cap

Shield Gas

Distributor

Tip

Plasma Gas

Distributor

Electrode Cartridge

35-1048 35-1089 35-102235-1015 35-1038 35-1284 35-1063

Material

Thickness

Pre Flow

Pressure

)

Cut Flow Rates /

Pressures Arc

Voltage

Edge Start

Kerf Width

@ Rec.

SpeedPlasma (N

)

Shield

O)*

Edge Start

Torch

Working

Height

Travel

Speed

Initial

Piercing

Height

Pierce

Delay

Edge Start

Material

Thickness

Pre Flow

Pressure

)

Cut Flow Rates /

Pressures

Kerf Width

@ Rec.

Speed

Plasma (N

)

Shield

O)*

Torch

Working

Height

Travel

Speed

Arc

Voltage

300A

Aluminium

Plasma / H

O Shield

Edge Start

Initial

Piercing

Height

Pierce

Delay

(mm)

Cartridge

Electrode

Shield

Shield Gas

Distributor

Tip

Plasma Gas

Distributor

Shield Retainer

Art # A-07917_AC

This Art Is For Reference ONLY

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 45 46

Commentaires sur ces manuels

Pas de commentaire

Tweco Torch Data for Auto-Cut O2 V.1 Manuel d'utilisateur Page 35

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Tweco Torch Data for Auto-Cut O2 V.1