Tweco Fabricator 141i Operating Manual Manuel d'utilisateur Page 32
- Page / 104
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Fabricator 141i
INSTALLATION, OPERATION AND SETUP 3-2 Manual 0-5145
WARNING
The Fabricator 141i must be electrically connected by a qualified electrical trades-person. Damage to the
PCA (Power Control Assembly) could occur if 140 VAC or higher is applied to the Primary Power Cable.
WARNING
ELECTRIC SHOCK can kill; SIGNIFICANT DC VOLTAGE is present after removal of input power. DO NOT
TOUCH live electrical parts.
SHUT DOWN welding Power Source, disconnect input power employing lockout/tagging procedures. Lock-out/
tagging procedures consist of padlocking line disconnect switch in open position, removing fuses from fuse box,
or shutting off and red-tagging circuit breaker or other disconnecting device.
Electrical Input Requirements
Operate the welding Power Source from a single-phase 50/60 Hz, AC power supply. The input voltage must match
one of the electrical input voltages shown on the input data label on the unit nameplate. Contact the local electric
utility for information about the type of electrical service available, how proper connections should be made, and
inspection required. The line disconnect switch provides a safe and convenient means to completely remove all
electrical power from the welding power source whenever necessary to inspect or service the unit.
Do not connect an input (WHITE or BLACK) conductor to the ground terminal.
Do not connect the ground (GREEN) conductor to an input line terminal.
• Correctlyinstalled,ifnecessary,byaqualifiedelectrician.
• Correctlyearthed(electrically)inaccordancewithlocalregulations.
• Connectedtothecorrectsizepowerpoint,fuseandprimarysupplyleadbasedonTable3-1.RefertoTable
3-1.
WARNING
An electric shock or fire hazard is probable if the following electrical service guide recommendations
are not followed. These recommendations are for a dedicated branch circuit sized for the rated output
and duty cycle of the welding Power Source.
50 / 60 Hz Single Phase Supply
Supply Voltage 115V AC
Input Current at Maximum Output 28.4 Amps
Maximum Recommended Fuse* or Circuit Breaker Rating
*Time Delay Fuse, UL class RK5. Refer to UL248
Maximum Recommended Fuse^ or Circuit Breaker Rating
^Normal Operating , UL class K5. Refer to UL248
30 Amps
30 Amps
Single Phase Generator Requirement 5 KW
Minimum Recommended Input Cable Size 12AWG
Maximum Recommended Input Cable Length 10ft (3m)
Minimum Recommended Grounding Cable Size 12AWG
Table 3-1: Electrical Service Guide
- Operating 1
- WE APPRECIATE YOUR BUSINESS! 2
- YOU ARE IN GOOD COMPANY! 2
- WARNINGS 3
- TABLE OF CONTENTS 4
- Fabricator 141i 10
- WARNING 13
- CAUTION 13
- AVERTISSEMENT 16
- SECTION 2: INTRODUCTION 25
- Manual 0-51 27
- This Page Intentionally Blank 30
- Art # A-09845 35
- Art # A-09828 36
- A-09587_AD 54
- Art # A-11576_AB 57
- Art # A-11483 59
- Art # A-11484 60
- Art # A-11486 60
- Art # A-8991_AB 61
- Art # A-08992_AB 61
- Art # A-08997_AD 64
- Art # A-11577_AD 66
- Art A-07691 72
- Art # A-07692 72
- Art# A-07693 72
- Art # A-07694 72
- Art # A-07698 75
- Art # A-07701 76
- Art # A-07702 76
- Art # A-07703 77
- Art # A-07704 77
- Art # A-07705_AB 78
- Art # A-07707 79
- Art # A-07708 79
- Art # A-07709 80
- Art # A-07428_AB 80
- Art # A-07713_AB 80
- Art # A-05867_AC 82
- TROUBLE SHOOTING AND SERVICE 88
- 5-2 Manual 0-5145 88
- Art # A-11807 90
- SECTION 6: KEY SPARE PARTS 91
- 2 Manual 0-5145 98
- APPENDIX 100
- 4 Manual 0-5145 100
- WARRANTY SCHEDULE 103
- T ECHNOLOGIES 104
Produits connexes et manuels pour Matériel Tweco Fabricator 141i Operating Manual
(92 pages)
(2 pages)
LG GR-P277AVH manuály
Uživatelské manuály a uživatelské příručky pro Ledničky LG GR-P277AVH.
Poskytujeme 1 manuály pdf LG GR-P277AVH ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels